Stop Wasting Time Waiting for Your Oven to Heat Up Let’s be honest: standing around waiting for a commercial oven to hit the right temperature...

Getting Your Heating Right on KOSME and Husky HyPET Systems If you’re running high-speed Husky HyPET systems, you already know that just...

Getting the Heat Right in Your PET Preforms If you’re running Husky HyPET systems, you know that just cranking up the wattage isn’t the...

Stop Fighting with Your SIPA Blower Heating If your SIPA rotary blower is acting up, you know exactly how it looks. You get those annoying thin walls...

Can a few new lamps actually save your old blow molder? If you’re running an older Techne blow molder and your cycle times are dragging,...

Making SMF Infrared Lamps Actually Work for Everyone If you’ve ever dealt with PET blow-molding, you know the struggle. Get the heat slightly...

Getting Your Rotary Ovens Just Right with Nichrome IR Lamps If you’re running an automated kitchen, you know the struggle of keeping every...

Stop Messing With Your Oven Settings: Sidel-Compatible Lamps That Just Work Heating PET preforms is a bit of a balancing act. You need it hot enough...

Stop the Burn-out Cycle on Your SIG Blomax Lines There is nothing worse than a tube burning out right in the middle of a run. Everything stops. Your...

Getting Heat Where It Actually Matters in Your PET Preforms If you’re running Sacmi SBF 12/24 or Husky HyPET systems, you know the struggle....

Stop Messing With Your Oven Hardware Every Time a Lamp Pops Nobody wants to spend their afternoon hacking away at an oven rack or rewiring a control...

Stop Wasting Time Waiting for Your SACMI Oven to Warm Up If you’ve ever stood there watching a SACMI rotary blower during a cold start, you know the...

Stop Fighting Your Oven: Getting Sidel Matrix Lamps Right Here is the problem when you swap out heating lamps in a Sidel Matrix blower: the...

Getting Your Sidel Matrix Oven Back in Balance Here is the problem with swapping out OEM lamps in a Sidel Matrix oven: if the heat profile shifts,...

Stop the Burn-outs on your SIG Blomax 4 There is nothing worse than a tube burning out right in the middle of a run. Everything stops. Your OEE...

Stop Overpaying for Your Blow Molding Lamps If you’re running SIG Blomax or Krones Contiform machines, you know the drill. It’s a...

Getting Your Pizza Oven Heat Just Right When you’re running a kitchen, consistency is everything. It all comes down to how the heat hits the...

Stop Replacing Your Heating Lamps Every Other Week If you’re running SIG Blomax or Krones Contiform 3 lines, you know the headache. One of...

Getting Your SACMI Line Back Up to Speed: The Sidel SBO 2002406262 Lamp When you’re running SACMI rotary blow molding lines, every single...

Getting Your Krones Contiform S Heating Back on Track If you’re running an older Krones Contiform S, you already know the headache. The heating...

Stop Fighting Your KHS Oven: A Better Way to Handle Heat If you’ve spent any time on the floor with a KHS blow molding machine, you know the...

Getting Your SIG Blomax 6 Back Up to Temp When you’re running a SIG Blomax 6 or a similar PET blowing setup, the last thing you want to deal...

Introduction We built this infrared (IR) buffet lamp with one thing in mind: hitting disinfection temperatures the instant you flip the switch....

On the blow molder, the heating section is where the whole line gets its rhythm—or loses it. If the preform doesn’t come through the heating...

On a rotary SIPA SFR 16 line, preform heating is the first choke point. As the lamps age, the heating tunnel starts drifting—thin necks get scorched...

On a PET line, the heating tunnel sets the pace. When a Krones heater lamp burns out, you bleed time on every restart—waiting for thermal stability,...